1.開機前準備工作
(1)檢查抽熱風管鍘刀是否打開。
(2)檢查電源及電機電源，北面進球處是否有異物。
(3)將提升機，輸送架位置是否擺放好。
2.開機順序
(1)打開抽熱風管鍘刀后，打開1號或2號風機，直至有熱風出來。
(2)打開烘干機電機，提升機電機。
(3)運轉正常后將待烘干物品每次一袋倒入北面烘球入口處。
3.關機順序
(1)檢查烘干機內有無物料投出。
(2)先關閉1號或2號風機電源，在把抽熱風管鍘刀關閉。
(3)依次關閉烘干機電源及提升機電源。
4.注意事項
(1)開機烘球時，應先將烘干機運轉一會，看是否有黃球出現。如有出現，應先用廢球倒入烘球投料口，直至烘球出料口無黃色異物等出現，才能正常生產。
(2)如以上辦法還不能解決，應叫機修工把烘干機出料口處蓋子開打，然后進入烘干機內把機內黃球異物等清理出烘干機，清理干凈后把出料口出蓋子蓋好，在運轉試生產。
中譯英：
1 Preparations before starting
(1) Check the pumping hot air pipe cutter is open.
(2) Check power and motor power, the goal is whether foreign bodies.
(3) Lift, transport rack positioned well.
2 Boot sequence
(1) Open pump air pipe cutter, opened in 1or 2, fan, until the hot air out.
(2) Open the drying machine, hoist motor.
(3) Normal operation will be dry goods every time a bag into the north entrance to bake the ball.
3 Shutdown sequence
(1) Check the drying machine has no material cast.
(2) The first closed in 1or 2, the power switch of the fan, the hot air pipe cutting off pump in.
(3) Turn off power and enhance machine drying machine.
4 Matters needing attention
(1) Boot drying ball, first drying machine running for a while, to see if there is a yellow ball. If have, should use the waste ball into a baking ball feeding mouth, to bake the ball outlet no yellow such as foreign bodies, the normal production can.
(2) If the above methods can not solve, should call the mechanic to dryer outlet lid open, then enters a drying machine to machine Neihuang ball foreign bodies such as clearing and drying machine, clean up after the outlet lid cover, in the operation of pilot production.
(圖/文http://www.alingl.cn/)
加入收藏
